1-Axis NEMA 34 Stepper Motor 1160oz-in & Driver PSR8078 48V Power Supply Kit | Обустройство дома

---

What’s in Box?

• 1 × PrimoPal's NEMA 34 Hybrid Stepper Motor, MPN PHB86S114-802 • 1 × PrimoPal's Stepper Motor Driver, MPN PSR8078 • 1 × Mean Well's Switching Power Supply, MPN NES-350-48 • 1 × Breakout Board & DB25 cable (for-free offering)     Stepper Motor Description This stepper motor (MPN PHB86S114-802) is supplied by one of the China's top stepper motor suppliers (PrimoPal Motor). It's a NEMA 34 hybrid stepper motor with 1.8° step angle (200 steps/revolution) and double flats shaft, made of high-quality cold roll sheet copper and anti-high temperature magnetic steel. The rated current is 5.6A per phase, allowing for the holding torque of 820Ncm (1160oz-in), if connected as bipolar-parallel. This high-performance and high-reliability motor is terminated with 8 flying ended lead wires, providing the maximum flexibility for your applications, including bipolar-series, bipolar-parallel and unipolar.     Stepper Motor Specifications • Electrical Specs

  • Physical Specs

  • Wiring Diagram

 

 

Stepper Motor Driver Description This stepper motor driver PSR8078 is supplied by one of the China's top stepper motor drive suppliers (PrimoPal Motor). The PSR8078 is a high-performance microstepping Drive based on pure-sinusoidal current control technology. Owing to the above technology and the self-adjustment technology (self-adjust current control parameters) according to different motors, the driven motors can run with smaller noise, lower heating, smoother movement and have better performances at higher speed than most of the Drives in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors. PSR8078 is suitable for a wide range of stepping motors, from NEMA size 23 to 42. It can be used in various kinds of machines, such as X-Y tables, labeling machines, laser cutters, engraving machines, pick-place devices, and so on. Particularly adapt to the applications desired with low noise, low heating, high speed and high precision.   Key Features:     Stepper Motor Driver Specifications • Electrical Specs

  • Pin Assignment and Description

This stepper motor drive PSR8078 has two connectors, connector P1 for control signals connections, and connector P2 for power and motor connections. The following tables are brief descriptions of the two connectors.

 

Connector P1 Configurations

  Connector P2 Configurations   • Microstep Resolution Selection

 

• Dynamic Current Setting

 

• Outline Drawing                                                            • Typical Connection             

         

 

 

Power Supply Description This switching power supply (MPN NES-350-48) is supplied by one of the world's top power supply suppliers (Mean Well).   Key Features: • AC input range selectable by switch
• Protections: Short circuit / Overload / Over voltage / Over temperature
• Forced air cooling by built-in DC fan
• Withstand 300VAC surge input for 5 seconds
• Built-in cooling fan On-OFF control
• Built-in constant current limiting circuit
• LED indicator for power on
• 100% full load burn-in test
• Fixed switching frequency at 90KHz
• Low cost, high reliability
• 2 years warranty     Power Supply Specifications     • Mechanical Drawing

 

 

Breakout Board Description Key Features • Can connect 6 drives and control 6 motors at the same time. • Built-in DB25 female connector. • DB25 connector output pinout: P1~P9, P14, P16, P17. • DB25 connector input pinout: P10~P13, P15. • DB25 GND pinout: P18~P25. • +5VDC power supply can be connected. • Support MACH3 software. • Built-in optical-coupler.   Output & Input Signals

Output Signals

 

Input Signals

• P10~P13, P15 - could be set for emergent stop and X, Y, Z limit switch

 

    Transaction Terms • Shipping Time and Terms

 

• Payment Terms

 

• Warranty & Refund

 

• Leaving Feedback to Us