Portable Pocket Pen Water PH Meter Digital Tester Quality for Aquarium Pool and LCD TDS3 Temp PPM 17% | Инструменты

Portable Pocket Pen Water PH Meter Digital Tester Quality for Aquarium Pool and LCD TDS3 Temp PPM 17% | Инструменты

Portable Pocket Pen Water PH Meter Digital Tester Quality for Aquarium Pool and LCD Digital TDS3 Temp PPM Tester

Easy to Use: Simply immerse the pH meter electrode in the solution to be tested, readings are quickly display on a large lcd display

Wide Application: Ideal instrument for any aquarium, the fishing industry, swimming pools, spa, school laboratories, food & beverage, drinking water etc.

Auto Calibrated: Features in-built calibration with 2 buffer powders(included).Just press a button to finish the calibration. This pH meter is factory calibrated. Users can use it directly.

Fast and Accurate Results: No need to work with those annoying color charts and test strips.Resolution: 0.01 pH, Accuracy: ±0.01 pH

Compact Portable Design: Pocket fitting pH meter that's also lightweight and compact. Total concealed fit in your bag or pocket for easy, casual carrying.

PH

Key Features:

Display: LCD Digital

Accuracy: 0.01

Resolution: 0.01

Operating Temperature: 0~60°C

Measuring Range: 0.00~14.00

Probe Type: Precision glass bulb electrode

TDS

Test the quality of various water ensuring you are enjoying the best quality water.

 Ideal for using in the following situations: drinking water water filters hydroponics aquariums food&coffee pools&spas. TDS range: 1-9999PPM/mg / L.

 Auto shut-off: 10minutes.

Data hold. Auto temperature compensation.

Accuracy: ±2%.

Dimensions: 14.2*2.3*1.3(CM)

Battery: 2×LR44 cell batter(NOT INCLUDE)

1.Remove protective cap.

2.First rinse the electrode with distilled water and suck it with filter paper.

3.Turn the meter on by pressing “ON/OFF” key.

4.Immerse the pH meter electrode in the solution to be tested (should not be over the immersion line).

5.Stir gently and wait around 30 seconds till the reading stabilizes.

6.After finishing, clear the electrode with pure water, turn the meter off by pressing “ON/OFF” key.

7.Always replace the protective cap after use.

1.Turn on PH meter

2.Disolve each buffer solution in 250ML of distilled water

3.Immerse the electrode into the PH 6.86 solution,(under the temperature of 25)

4.Press the “CAL”(calibration)button for 5 seconds and release

-Display will start flashing 6.86

-Wait until the display stops flashing.

Rinse the electrode with distilled water and dry it with filter paper.

5.     Immerse the electrode in PH 4.00 solution,

-Press“CAL”button for 5 seconds,then press and release immediately second time

-Reading will start flashing 4.00

-Wait until display stops flashing

Rinse and dry the electrode with distilled water as before.

6.Place the meter back to the buffer solution to test calibration.If incorrect,please repeat the calibration

7.If approximate PH of your test solution is known to be above 7.0,calibrate the meter using 6.86 and 9.18 solution. To do this,please follow the calibration chart,The third step is the calibration method for 9.18 point.

1) pH Meter

2)2 Bags Buffer Powder

3)Instruction Manual

4)TDS Meter

5)Leather Bag

Kindly Reminder:

If the tester was used or lay aside long time: recalibrate it.

If you open battery case or replace battery: recalibrate it.

The glass bulb of the electrode is fragile. Don't touch it by hard tools and fingers, suck the water on it gently when cleaning.

come without retail box and battery, and it need LR44 cell BATTERY