4q controller 24v dc 100A for permanent magnet motor | Обустройство дома

4q controller 24v dc 100A for permanent magnet motor | Обустройство дома

4q controller 24v dc controller 100A for permanent magnet motor

Model: DC24RT100BL

high current four quadrant reversible regenerative pwm 48 volt 24 volt dc motor speed controller 100A

Connection about speed control potentiometer:

The operation of speed control potentiometers should follow above instructions in Figure 6. Fit 10K regulator potentiometer between 5V terminal, IN terminal and 0V terminal.

Caution:
he connecting wire of speed control potentiometer should be away from conductors of power input terminal and output in sake for reducing unnecessary interfere of electronic signals. The length of connecting wire should be shorten as far as possible. If the length is over 0.5m, the shielding wire is recommended

You also can control the motor speed by analog signal 0-5V, connect drawing as below:

Function and connection about control terminal:
Notice:
Connecting wires of speed control terminals should be away from conductors of power input terminal and output in sake for reducing unnecessary interfere of electronic signals. The length of connecting wire should be shorten as far as possible. If the length is over 0.5m, the shielding wire is recommended.

BRAKE:
Regenerative braking control: When quick stopping of motor is required, this function is suitable. Close brake switch, motor controller rapidly brakes motor’s speed by the way of regenerative braking then make motor stop immediately.
EN:
Enable control: Control the start and stop of motor
Open external enable switch, motor controller will automatically lock in internal circuit and make motor stops.
Close external enable switch,motor will start to rotate at the speed value set by potentiometer or input analog signals.
Note:
A.When regenerative braking, the motor’s stop time is decided by set value of brake current (“REGEN  CL” potentiometer set current )or set value of soft stop (“DECEL” potentiometer set soft stop time).
Eg. If the set value of brake current(“REGEN  CL” potentiometer set current ) is high and the set value of soft stop time(“DECEL” potentiometer set soft stop time) is low,  the motor’s brake time will be shorten.

B.When close brake switch, rotate speed value after braking is decided by set value of “MIN SP” potentiometer (means Min speed ). Eg. If the “MIN SP” potentiometer set the value “0”, then after brake, the motor rotate speed will be “0”. If the “MIN SP” potentiometer set the value “N”, then after brake, the motor rotate speed will be “N”.

DIR: Reversing (Direction)control terminal:
The reversing control of motor: Rotation direction can be easily get through open or close reversing switch. 

Introduction and setting of adjustable potentiometer:

1. “ACCEL” potentiometer( Set soft start time ):
Adjust “ACCEL” potentiometer to set ramp up from initial speed value to setting speed value(it means acceleration time, the time can be adjusted between 0.2 seconds and 20 seconds).Please see the below Figure.
Note: Adjust this potentiometer in counter-clockwise to shorten soft start time while adjust this potentiometer in clockwise to prolong soft start time.

2. “DECEL” potentiometer( Set soft stop time ):
Adjust “DECEL” potentiometer to set ramp down from Max.speed value to Min.speed value(it means deceleration time, the time can be adjusted between 0.2 seconds and 20 seconds).Please see the below Figure.
Note: Adjust this potentiometer in counter-clockwise to shorten soft stop time while adjust this potentiometer in clockwise to prolong soft stop time.

3. “FWD MAX SP” potentiometer(set Max. forward speed value):
Adjust this “FWD MAX SP”potentiometer to set motor’s Max. forward speed value(it is also be used to limit motor’s Max. forward speed value). When adjust this potentiometer in clockwise, forward speed value is increased.

4. “REV MAX SP” potentiometer(set Max. reverse speed value):
Adjust this “REV MAX SP”potentiometer to set motor’s Max. reverse speed value(it is also be used to limit motor’s Max. reverse speed value). When adjust this potentiometer in clockwise, reverse speed value is increased.

5. “REGEN CL” potentiometer(set regenerative braking current value):
Adjust “REGEN CL” potentiometer to limit Max. braking armature current value(it also means brake/stop time). The braking current value affect brake/stop  time. When adjust this potentiometer in clockwise, the braking current value will be increased.

6. “IR COMP” potentiometer(set torque compensation):
Adjust “IR COMP” potentiometer to make motor have constant speed value in different load conditions(Before the motor controller is delivered out of factory, the torque compensation generally set”0”). When adjust potentiometer in clockwise, torque compensation value is increased.

7. “MIN SP” potentiometer(set Min speed value):
When external given signal is “0V”(or adjust external signal setting potentiometer at end in counter-clockwise),adjust “MIN SP” potentiometer to set motor’s Min speed value(Generally this potentiometer is set “0”,before the motor controller is delivered out of factory).

8. “MOTOR CL” potentiometer(set motor’s rated current):
Adjust “MOTOR CL”potentiometer to limit motor controller’s Max.output current(we also says motor’s setting current value).The setting of this current should be based on motor’s rated current value.Current value should be moderate.If not,torque is not enough or overcurrent protection is failure. Adjust this potentiometer in clockwise to increase motor controller’s output current.
Note: Motor controller’s output current value should be twice as much as motor’s rated current value in general.However,motor controller can’t  operate at setting value which is greater than motor’s rated current value for a long time, or the motor will be burnt out.

4q controller 24v dc controller 100A for permanent magnet motor

4q controller 24v dc controller 100A for permanent magnet motor

Jinan Keya Electron Science and Technology Co., Ltd, founded in 2001, has been trading in the research &development, manufacturing and sales of DC Servo motor and Servo control system for 15 years. Company set technology, talent, management and other resources advantages, to effectively integrate, has maintained a healthy, stable and rapid growth.

The company has adopted ISO9001:2008 quality management system certification, products through the CE certification. More than 3000 large and medium-sized domestic equipment manufacturers designated as supporting products, and exported to the United States, Europe, Southeast Asia and other countries.

We devote ourself to Research & Development, welcome Costom-made products, if you need some unusual products, let's have further communication.

Delivery time: 1-3 working days after receive the payment

4q controller 24v dc controller 100A for permanent magnet motor

 1.    Q: What are your main products?

      A: We produce various kinds of dc motor & controller.

2.    Q: How long have you been in this field?

      A: More than 15 years in this field.

3.    Q: Do you have your own R&D team?

      A: Yes. R&D is our core competitiveness, continuous innovation is just what we are seeking for all       the time. Some of our engineers have more than 20years experience in the industry, and we also         cooperate with colleges, scientific research institutions and large enterprises.

4.    Q: How soon can you deliver the goods?

      A: That depends on the exact model you order. For regular products, usually we will prepare some units in stock, we can deliver them within 3 working days.

5.    Q: Can you make the product according to customer’s requirements?

      A: Yes, welcome costom-made products.

6.    Q: What is your payment term?

      A: You can pay by TT, Paypal, Western Union.